I would be happy to make a recommendation for you.
For a trailer brake controller I highly recommend the tried and true Tekonsha Prodigy P3 # 90195 due to its easy to read LCD screen, built in diagnostics that are easy to understand, and it being a proportional controller meaning the trailer brakes will be applied with the same intensity that you apply the brake pedal.
To power the P3 # 90195 your 2007 Internation Trucks 4100 Dump Truck will need to have a 7-way RV connector installed.... view full answer...
You are going to want to use the Hayes Air Actuated Trailer Brake Controller # HA100400C on your 2018 International LT625. With this brake controller it will tie into your existing air lines for your brakes and use the pressure in the air lines to proportionally match the braking force applied to the electric trailer brakes.
The only connections you will need to make are for the Air Line # RM450700, and electrical connections. The white wire from the Hayes controller will go to a 12 volt... view full answer...
Behind the brake pedal there is a switch that has wires ran to it that you'll need to test with a circuit tester part # PTW2993 to test all of the wires until you find the circuit that only has 12 volts when the brake pedal is pressed. view full answer...
The Hayes Air Actuated Brake Control, # HA100400C, will work on your 2002 International 4400 truck as long as you have an air line connection and trailer connector to plug your trailer up to your truck.
You will need to wire the three wires coming out of the Warner controller as followed: BLACK is to 12-volt power, the RED will wire to the your brake light switch on your brake pedal, and the BLUE wire will wire into the 7-way connector to run the brake signal to the trailer when it is... view full answer...
For your 2009 International 4300 with air brakes you will use the Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional # HA100400C and then the HydraStar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi # HBA16 or if you have drum brakes # HBA-12.
This combination will convert your air brakes into a proportional braking system on your trailer. view full answer...
Yes it will; a truck with air brakes is 100 percent compatible with the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.
The type of brakes your truck has won't matter so long as the circuit that activates the truck's brake wire signal has voltage on it when you press the brakes.
I have added a link below to a video review for you to check out as well of the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. view full answer...
The best suspension modification you can make for an RV is a rear sway and for your 2018 Nexus RV that is on a 2017 2016 TerraStar International chassis you would want the rear sway bar part # RM-1179-112.
Next in line would be going with an aftermarket front sway bar. For that you would want the part # RM-1179-124 which is also a confirmed fit. view full answer...
In addition to the rear anti-sway bar # RM-1179-112 for the 2016 International Terrastar we also have the front anti-sway bar, # RM-1179-124. Please note that for the REAR bar if the RV does not have OnSpot chains, you must purchase axle plate kit # RM-590060-00 to install the bar.
There isn't a steering stabilizer available for this particular model. view full answer...
A brake controller does not have to be tied into the computer on your 2007 International 4200. A brake controller such as # 90885 requires 12 volt power in to power the controller, a ground which is usually attached to the negative battery terminal, an output wire (blue) goes to the trailer connector, and a connection to the cold side of the brake switch to tell the controller when you are stepping on the brake pedal.
If your truck has air brakes then it is possible that there isn't a... view full answer...
Installation of a trailer brake controller like the Tekonsha Voyager # 39510 in your 1998 International 3400 Series bus will require a trailer brake installation kit, part # ETBC7, along with the controller itself. Since your vehicle is fairly long you will need extra wiring # 10-2-1 (sold by the foot) to let you reach all the way back to your rear bumper.
We do not have a video for Voyager installation in your specific vehicle but the linked article covers installation of the # ETBC7... view full answer...
Since there isn't an adapter to go from a semi 7-Way to an RV 7-Way the best solution is going to be to install a separate RV style 7-Way on your 2007 International 4400.
You can use installation kit # ETBC7. You may be able to tap into the circuits on the existing 7-Way as long as the turn signals and brake lights are combined on the same circuit. If not then you will have to first install a 4-Way using # 119178KIT.
If the circuits are combined on the existing semi 7-Way then all you... view full answer...
We can get your International 4900 set up with a 7-way and brake controller, and to do that you'll need to start with a 4-way, which will activate your trailer's lighting functions, and you'll then plug that into the 7-way. For the universal harnesses and brake controller, use the following:
- Tail Light Converter with 4-Pole Flat Trailer Connector # C59236
- Universal Installation Kit for Trailer Brake Controller # ETBC7
- Prodigy P3 Trailer Brake Controller # 90195
The # ETBC7 has the... view full answer...
The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper part # 3371809050 is a universal product which can be made to fit many different applications. I wouldn't be able to inform on specific applications such as this but so long as you have the 34" frame spacing (outside to outside) which is standard then it should be able to be made compatible. If not, a better option would be the Buyers Products Fabricators Hitch Plate part # 3371809042 which is not limited to the above frame spacing... view full answer...
We may have a solution for you.
To wire a brake controller on your 2007 International Trucks 4300 Series, you need to wire the controller's red wire to the stop light circuit. If the only wire you've found for brake lights is tied to the turn signal lights, then that wire cannot be used. The reason is that the turn signals, once engaged, would activate the brakes.
There may be a brake switch circuit that is sometimes abbreviated as the CHMSL circuit. Use a tester like part # PTW2993 to... view full answer...
OnSpot Chains are a special tire chain system for snowy weather (pictured below). Basically the sway bar is going to need the same space for mounting as the OnSpot chains so they can't be used together with the # RM-1179-110-00 you were looking at.
If you have OnSpot chains on your 2020 International Trucks DuraStar then you'll want the Roadmaster Rear Anti-Sway Bar # RM-1179-110.
If you don't have OnSpot chains on your 2020 International Trucks DuraStar then you'll want the Roadmaster... view full answer...
The inner bracket width of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A is 34-1/4" plus or minus 0.06" according to my contact at Buyers Products.
Attached is a photo showing this dimension for you. view full answer...
The label side of the Tuson Electronic Sway Control System for Electric Trailer Brakes # 335TSC-1000 needs to face forward and be in a vertical orientation perfectly centered on the trailer 5-10 feet back from the center of the king pin like what you see in the picture I attached.
That said, for the type of sway you are experiencing your best solution it so move your axles further back on your trailer. view full answer...
For your 2015 International Prostar I recommend the Buyers Products Weld-On Pintle Hitch Plate # 3371809027A. The plate dimensions are 25-1/2" tall x 34-1/2" wide x 3/4" thick. It is a fabricators hitch plate so you will need to take it to a certified welder or fabricator for installation. This is the best option since there are no custom fit hitch plates for your truck. view full answer...
Though The Curt Echo Under-Dash Wireless Brake Controller # C27JR will work with your 2004 International 4300.
Before installing a brake controller you will have to find the 7 wire plug in the frame rail behind the cab which contains the wires for lights and signals. From there you will have to wire that into the wiring kit # ETBC7. You will have to cut off the 4-way on the ETBC7 and then use a circuit tester # PTW2992 so you can determine all the functions of the wires on your truck.... view full answer...
Go To Results